Table of Contents
Bitumen PG 82/22
Nrog nws qhov tshwj xeeb nkag mus rau qib 82 thiab qib viscosity ntawm 22, Bitumen PG 82/22 ua kom muaj kev ua tau zoo tshaj plaws hauv ntau daim ntawv thov kev tsim kho. Nws cov khoom zoo siab ua rau nws nyiam xaiv rau paving, waterproofing, thiab sealing tej yaam num.
MSDS ntawm Bitumen PG 82/22
Cov ntawv thov hauv Kev Tsim Kho
Paving Solutions
Nws yog qhov zoo tagnrho rau kev tsim cov khoom ruaj khov thiab kav ntev asphalt pavements, muaj peev xwm tiv taus tsheb loj loads thiab huab cua tsis zoo.
Waterproofing
Cov khoom no ua haujlwm zoo heev waterproofing tus neeg sawv cev, tiv thaiv cov qauv ntawm cov dej infiltration thiab ua kom lawv lub neej ntev.
Sealing
Nws kuj tseem siv tau rau sealing cov kab nrib pleb thiab cov pob qij txha hauv pavements, txhim kho lawv cov qauv kev ncaj ncees thiab tiv thaiv kev puas tsuaj ntawm dej.
Cov txiaj ntsig ntawm Asphlat PG 82/22
Durability: Ua kom muaj kev ua haujlwm ntev ntev thiab txo cov nqi kho.
versatility: Haum rau ntau hom kev tsim kho.
Kev yooj yim ntawm daim ntawv thov: Muab kev yooj yim ntawm kev tuav thiab daim ntawv thov, txuag lub sijhawm thiab nqi zog.
Qhov zoo tshaj cov neeg sib tw
Piv nrog rau lwm cov qib bitumen, Asphalt PG 82/22 muaj kev txhim kho durability, zoo adhesion, thiab superior tsis kam rau deformation, ua rau nws yog qhov kev xaiv rau xav tau kev tsim kho tej yaam num.
Ntim lub ntsiab
Ntim rau hauv cov thawv ntim khoom zoo tsim los tiv thaiv kev sib kis, noo noo, thiab kub hloov pauv. Kev ruaj ntseg ntim cov kev daws teeb meem kom ntseeg tau cov khoom lag luam zoo thaum thauj thiab khaws cia.
Specification ntawm Bitumen PG 82/22
|
Description |
Tsev |
Tus nqi |
Txoj Kev Kuaj |
|
Qhov nruab nrab 7-hnub Max. Pavement Design Temp |
° C |
ASTM D6373 |
|
|
Yam tsawg kawg nkaus Pavement Design Temperature |
° C |
>-22 |
ASTM D6373 |
|
ORIGINAL BINDER |
|||
|
Flash Point Temp, T48: Yam tsawg kawg nkaus |
° C |
230 |
ASTM D92 |
|
Viscosity Max. Kev ntsuas kub |
Pa S |
3.0 |
ASTM D4402 |
|
Dynamic Shear, TP5: Min 1.00 kPa test temp @ 10rad / s |
KPa |
1.00 Min |
ASTM D6373 |
|
ROLLING THIN FILM CEV (T240) |
|||
|
Loj poob, siab kawg, feem pua |
% |
1.00 |
ASTM D6 |
|
Dynamic Shear, TP5: Min 2.20 kPa test temp @ 10rad / s |
KPa |
2.20 |
ASTM D6373 |
|
NYIAJ TSHUAJ VESSEL RESIDUE (PPI) |
|||
|
PAV Aging Temperature |
- |
100/110 |
- |
|
Dynamic Shear, TP5: Max 5000 kPa test temp @ 10rad / s |
KPa |
5000 max |
- |
|
PHYSICAL HARDENING REPORT |
|||
|
Creep Stiffness, TP1:S, Max 300.0MPa, Min 0.300 test temp @ 60s |
° C |
-12 |
ASTM D6648 |
|
Direct Tension, TP3: Failure Strain, Min 1.0% test temp @ 1.0mm / min |
° C |
-12 |
ASTM D6723 |